Bimetallic/Laminated Cast White Iron Wear plates are unique wear resistant materials in that they combine very high wear resistant qualities of a white iron(ASTM A532 15/3CrMo, 700BHN - 63HRc) with a weldable & high impact toughness mild steel through a metallurgical bond to create a product that is exceptionally resistant to impact and abrasion while retaining.
Bimetallic white iron wear plates for conveyor transfer point, for iron ore feeder chute, for Crusher liner protecion, for Blast furnace grate etc.
>Material: ASTM A532 15/3CrMo cast white iron((also named DOMITE), vacuum brazed onto mild steel base plate.
>Hardness: 700BHN / 63HRC
>Provide excellent abrasion resistance, high impact toughness;
>Installation: weld or by studs
Application: Widely used in the abrasion wear condition (gouging abrasion, high stress crush abrasion, low stress sliding abrasion)
Features:
1. Good properties of wear resistance, toughness, plasticity, heat resistance, hot hardness.
2. Easy for welding and assembly: Washers, Nuts, Studs, Threads, Holes are available.
3. Different shapes and sizes available
-Minimum thickness 12mm (6mm white iron + 6mm mild steel base);
-Maximum thickness 160mm
-Maximum dimension without splice L x W: 900x600mm
4. Smooth and flat surface
5. High cost-effective.
6. 3 times more higher usage life compared with overlay plates
Bimetallic white iron wear blocks, average hardness 63HRC min.
Typical Data Numbers We Received From Our End-Users:
>Usage life is 50% greater than that of Ni Hard Irons;
>At least 7 times longer than A.R. type steels 360/400 BHN;
>4 times the wear rate of 500 BHN A.R. Plate;
>5 times the wear rate of Manganese Steel;
>3 times the wear rate of Weld Hardfacing;
>16 times the wear rate of Carbon Steel;
Our Output for wear blocks is 500tons/month. usual inventories is about 300tons.
Output of overlay wear plate is 2000 sqm/month. Usually inventories is about 500sqm.
Plant area is about 8000 sq.m
Staffs: 87
Registered capital is 15 million RMB
Annual sales is about 1500-2000tons for wear blocks, 1000tons for overlay wear plates.
If you are looking for high quality wear-resistant or casting products, then you are just in the right place, please feel free to contact us with any inquiries, we are ready at your service at anytime.
Laminated Wear Blocks are unique wear resistant materials in that they combine very high wear resistant qualities of a high chrome cast iron (15/3CrMo, 700 BHN - 63 HRc) with a weldable & high impact toughness mild steel through a metallurgical bond to create a product that is exceptionally resistant to impact and abrasion while retaining.
We can also product other Bucket wear attachments.
>Bucket teeth.
>G.E.T. parts.
>Heavy duty equipment wear parts
>spare parts. Heel shrouds
>Bucket repaire and fabrication.
>White iron Castings.
>bi-metallic castings.
>Bimetal pipes
>shredder hammer tips
>Tungsten carbide wear parts.
>Ni-hard 4 wear plates, wear billets
| Chocky bars |
CB25, CB40,CB50,CB65, CB80,CB90, CB100,CB130,CB150 |
| Wear buttons |
WB6, WB75, WB90, WB110, WB115, WB150 |
| Wear blocks(standard) |
DLP201A, DLP 125, DLP184, DLP528, DLP619, DLP451, DLP450, DLP2230, DLP2017, DLP4, DLP919, DLP1191, DLP515, DLP200, DLP271, DLP270, DLP508, DLP115, DLP337, DLP1101, DLP343 |
| Hammer tips |
DLP1654,90X90X50mm; DLP653,90X90X45mm; DLP1927, 90X90X55mm |
Following are our laminated wear blocks:
Laminated wear blocks---the most common types are:
1) Chocky bars (CB 25. CB40, CB50, CB65, CB80, CB90, CB100, CB130. CB150)
2) Standard wear bars (DLP201A, DLP 125, DLP184, DLP528, DLP619, DLP451, DLP450, DLP2230, DLP2017, DLP4, DLP919, DLP1191, DLP515, DLP200, DLP271, DLP270, DLP508, DLP115, DLP337, DLP1101, DLP343 )
3) Shaped wear bars
4) Wear buttons& donuts(WB60, WB75, WB90, WB110, WB115, WB150, DLP1920, DLP1921, DLP1994, DLP2196)
5) Shredder/Grinder hammer tips (DLP1654,90X90X50mm; DLP653,90X90X45mm; DLP1927, 90X90X55mm)
6) Bi-metallic wear plates
7) Knife edges(DLP1065-22, 203X22X50MM; DLP1265-22,305X22X50MM; DLP1065A-16, 203x16x50mm, DLP1065A-25, 203x25x62mm; DLP1265A-25, 305x25x56mm)
8) Skid bars, skid blocks(DLP412, 250x150x45mm; DLP413, 200x150x45mm; DLP414, 250x250x45mm)
9) Wafer strips, WS25, WS40, WS50, WS65;
10) Elbow wear blocks
11) Other sizes and shapes
12) Multi-function gradient cutter tooth
13) Rockbox liners
14) Micro-ledges
Overlay wear plates: standard sheet size 1500x3000mm, thickness 4+4(8mm), 6+4(10mm), 6+6(12mm), 8+5(13mm), 8+6(14mm), 10+5(15mm), 10+10(20mm), 12+12(24mm), 12+17(29mm).
Please contact us if you have any questions or comments:
Shing Xiao President, Sales
Wear Parts & Wear Solutions!
Audited Supplier 
){kind=link}
){kind=link}